设为首页 收藏本站
开启辅助访问 切换到宽版
注册会员 找回密码

VoIP88

toasterisk 发表于 2009-9-6 22:48 | 显示全部楼层 |阅读模式
Wanpipe Asterisk InstallTrixBox Installation
Elastix Installation
PBX in Flash Installation:
Asterisk Linux Source Installation
Asterisk FreeBSD Source Installation

Asterisk Third Party Instructions

Wanpipe TDM drivers just as Digium wct drivers, bind directly toZaptel.  Therefore full zaptel headers are needed in order to compileWanpipe TDM kernel drivers.

Before starting WANPIPE installation please download full Asterisk package from http://www.asterisk.org/downloads. Located on the right hand side of the page are the latest releases of each program.
Installing Asterisk/Zaptel (Linux)
  • Zaptel Installation
      
    Download zaptel into arbitrary directory (/usr/src) and  untar it.
    #>tar xvfz zaptel-<version>
    Make a symbolic link /usr/src/zaptel to the actual zaptel directory.
    #>ln -s zaptel-<version> zaptel
    #>cd zaptel
    #>./configure
    #>make
    #>make install
  • LibPRI Installation
    Download libpri into arbitrary directory (/usr/src) and untar it.
    #>tar xvfz libpri-<version>
    #>cd libpri-<version>
    #>make
    #>make install

  • Asterisk Installation
    Download Asterisk into aribrary directory  (/usr/src/) and untar it.
    Make sure that old asterisk modules are removed from /usr/lib/asterisk/modules
    #>tar xvfz asterisk-<version>.tgz
    #>cd asterisk-<version>
    #>./configure      (in case of Asterisk 1.4 or above)
    #>make
    #>make install
    #>make samples (in case of very first install)

Please note: (version) refers to the specific release of yourprogram. For instance, zaptel-1.2.5.tar.gz, once untarred will createthe folder zaptel-1.2.5.
   
Once zaptel, libpri and asterisk are downloaded and untarred, you may proceed with WANPIPE&reg; installation.
   
After completing the WANPIPE&reg; TDM installation, you may proceed to configuring the full Asterisk suite.


Wanpipe TDM/Zaptel Installation (Linux)


  • Download the appropriate WANPIPE&reg; Release based on the Sangoma Hardware. Refer to Wanpipe Drivers section.
  • Untar wanpipe release in arbitrary directory (/usr/src/ is recommended).
    #>tar xvfz wanpipe-<version>.tgz
    #>cd wanpipe-<version>
    After untarring WANPIPE&reg;, the wanpipe<version>/ directory will be created.
  • Run ./Setup install from the newly created wanpipe-<version> directory
         
              #>./Setup install
        or

               #>./Setup install --64bit_4GB  
                  (in case X86_64bit & 4GB memory or more)
      
    Proceed with installation Select "Y" for each option.  
    Under compilation mode:  Select "TDM Only drivers" (Option #2).

    Setup will ask you for location of zaptel sources?
    [By default Setup will look in /usr/src/zaptel]

    Zaptel 1.4 -> wanpipe drivers use zaptel supported hwdchan so no patching is needed.
                                 Zaptel does not need to be recompiled
      
    Zpatel 1.2-> Setup will ask you if you would like to add support for Sangoma HW HDLC DCHAN PRI to Zaptel.
                                   "Enable TDMV DCHAN Native HDLC Support & Patch Zaptel ? (y/n)"
                                    Select "Y" to Enable HW HDLC on DCHAN PRI in Zaptel.
                           Setup will ask you if you would like to recompile/reinstall Zaptel.
                                  "Recompile/reinstall zaptel (recommended) ? (y/n) "
                                   Select "Y" to recompile/reistall Zaptel
  • Proceed with Defaults for the rest of the compilation.
  • Last step in installation will ask you to configure wanpipe cards for Zaptel
    -> Proceed with YES this is your initial installation
    -> Note wancfg_zaptel configurator will overrite your zaptel.conf and zapate.conf files and
          save the originals as zaptel.conf.bak and zapata.conf.bak
    -> The configuration process continues on Configuration Section

    If any errors are encountered during the compilation of the utilities, click here for assistance.
  
Confirm Successful Wanpipe/Zaptel Installation
  • Confirm successful Wanpipe/Zaptel installation run:
    #>wanrouter hwprobe

    This command will load the wanpipe and zaptel modules and willprint out list of all Sangoma hardware installed on the system.
Installing Asterisk/Zaptel (FreeBSD)  

We recommend to use Asterisk/Libpri/Zaptel from FreeBSD Ports. You can visit this link for more details about Asterisk FreeBSD Project
  • Zaptel Installation
    You can skip the Zaptelinstallation if you are going to use Wanpipe from FreeBSD Ports(Wanpipe port will install Zaptel automatically). If you are going touse Wanpipe package, you need install Zaptel now.
    Change directory to /usr/ports/misc/zaptel
    #> cd /usr/ports/misc/zaptel
    #> make
    #> make install

  • LibPRI Installation
    Change directory to /usr/ports/misc/libpri
    #> cd /usr/ports/misc/libpri
    #> make
    #> make install
  • Asterisk Installation
    Change directory to /usr/ports/net/asterisk
    #> cd /usr/ports/net/asterisk
    #> make
    #> make install
    To install asterisk-addons, change directory to /usr/ports/net/asterisk-addons and run `make;make install`
Once Zaptel, Libpri and Asterisk are installed, you may proceed with WANPIPE&reg; installation.
   
After completing the WANPIPE&reg; TDM installation, you may proceed to configuring the full Asterisk suite.
Wanpipe TDM/Zaptel Installation for FreeBSD OS
  • Download the appropriate WANPIPE&reg; Release based on the Sangoma Hardware from ftp://ftp.sangoma.com/FreeBSD/wanpipe directory and execute following command:
                  #> pkg_add wanpipe-<version>.tbz
  • Installation utility will create /usr/local/wanpipe-<version>directory, untar all files into this directory and update packagedatabase with new wanpipe package.
    After this, installation utility will execute post-install script.  
    Proceed with installation Select "Y" for each option (if you don't want to load Wanpipe during boot sequence, say "No" for that questions).   Under compilation mode:  Select "TDM Voice Support Only " (Option #2).

    Setup will ask you for location of zaptel sources? Select Option #1 (as we recommend it)
  • Proceed with Defaults for the rest of the compilation.
If any errors are encountered during the compilation of the utilities, please contact out Tech support Team.

Confirm Successful Wanpipe/Zaptel Installation
  • Confirm successful Wanpipe/Zaptel installation run:
    #>wanrouter hwprobe

    This command will load the wanpipe and zaptel modules and willprint out list of all Sangoma hardware installed on the system.

Wanpipe Port TDM/Zaptel Installation for FreeBSD OS
We are in a process to commit Wanpipe driver into FreeBSD kernel.Until then, extra step will require in order to install Wanpipe portdistribution.
  • Change directory to /usr/ports/misc
  • Download the latest wanpipe-<version>-port.tar.gz from ftp://ftp.sangoma.com/FreeBSD/wanpipe/ports directory.
  • Untar it from /usr/ports/misc
    #> tar xvzf wanpipe-<version>-port.tar.gz
    This will create wanpipe directory under /usr/ports/misc directory.

  • Change directory to /usr/ports/misc/wanpipe
    #> cd /usr/ports/misc/wanpipe

  • Compile and install Wanpipe port:

    #> make
    Select compilation TDM_VOICE option.
    #> make install

If any errors are encountered during the compilation of the utilities, please contact out Tech support Team.

Confirm Successful Wanpipe/Zaptel Installation
  • Confirm successful Wanpipe/Zaptel installation run:
    #>wanrouter hwprobe

    This command will load the wanpipe and zaptel modules and willprint out list of all Sangoma hardware installed on the system.

评分

1

查看全部评分

cnasterisk 发表于 2009-10-20 09:02 | 显示全部楼层
来几张sangoma 4e1语音卡的图图

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有帐号?注册会员

x
stonecoolboy123 发表于 2010-11-15 11:05 | 显示全部楼层
openvox  A800P  如何安装驱动   
medou008 发表于 2010-11-30 20:57 | 显示全部楼层
了解一下!
小小姐姐189 发表于 2012-9-7 16:31 | 显示全部楼层
謝謝,希望以後多些










vlhdb 发表于 2013-4-1 19:34 | 显示全部楼层
回复一吧












国印刷综合门户网 printuser.org   天摄影在线网   haapa.cn    辽宁网    lnw.cc   
您需要登录后才可以回帖 登录 | 注册会员

本版积分规则

关闭

站长推荐上一条 /1 下一条

手机版|VoIP88 ( 粤ICP备11095982号   填写您的邮件地址,订阅我们的精彩内容:

GMT+8, 2017-9-24 23:36 , Processed in 0.289302 second(s), 32 queries .

Powered by VoIP88

© 2001-2017 VoIP88

快速回复 返回顶部 返回列表